The role of microbial electrogenesis in regulating methane and nitrous oxide emissions from constructed wetland-microbial fuel cell

This study assesses a sustainable solution to greenhouse gases (GHGs) mitigation using constructed wetland-microbial fuel cells (CW-MFC). Roots of wetland plant Acorus Calamus L. are placed in biological anode to better enable anode microorganisms to obtain rhizosphere secretion for power improvement. Three selected cathode materials have a large difference in GHG emissions, and among them, carbon fiber felt (CFF) shows the lowest emissions of methane and nitrous oxide, which are 0.77 ± 0.04 mg/(m²·h) and 130.78 ± 13.08 μg/(m²·h), respectively. The CFF CW-MFC achieves the maximum power density of 2.99 W/m³. As the influent pH value is adjusted from acidic to alkaline, the GHGs emissions are reduced. The addition of Ni inhibits GHGs emission but decreases the electricity, the power density is reduced to 1.09 W/m³, and the methane and nitrous oxide emission fluxes decline to 0.20 ± 0.04 mg/(m²·h) and 15.49 ± 1.86 μg/(m²·h), respectively. Low C/N ratio reduces methane emission, while high C/N ratio effectively inhibits nitrous oxide emission. At the influent pH 8 and C/N = 5:1, the methane emission flux is approximately 10.60 ± 0.27 mg/(m²·h), and the nitrous oxide emission flux is only 10.90 ± 1.10 μg/(m²·h). Based on the above experimental results by controlling variable factors, it is proposed that CW-MFC offers an environment-friendly solution to regulate GHG emissions.     

High Q×f values of Zn-Ni co-modified LiMg0.9Zn0.1-xNixPO4 microwave dielectric ceramics for 5G/6G LTCC modules

In this work, Zn-Ni co-modified LiMg_0.9Zn_0.1-xNi_xPO₄ (x = 0–0.1) microwave dielectric ceramics were fabricated using a solid state synthesis route. Rietveld refinement of the XRD data revealed that all ceramic samples have formed a single phase with olivine structure. SEM images showed that the samples have a dense microstructure, that agrees with the measured relative density of 97.73 %. Based on the complex chemical bond theory, Raman and infrared reflectance spectra, we postulate that ε_r is mainly affected by the ionic polarizability, lattice and bond energy, while P-O bond plays a decisive role in Q×f and τ_f value. Optimum properties of Q×f ~ 153,500 GHz, ε_r ~ 7.13 and τ_f ~ ?59 ppm/°C were achieved for the composition LiMg_0.9Zn_0.06Ni_0.04PO₄ sintered at 875 ℃ for 2 h. This set of properties makes these ceramics an excellent candidate for LTCC, wave-guide filters and antennas for 5 G/6 G communication applications.     

Ru-doped 3D porous Ni3N sphere as efficient Bi-functional electrocatalysts toward urea assisted water-splitting

Developing efficient, stable and ideal urea oxide (UOR) electrocatalyst is key to produce green hydrogen in an economical way. Herein, Ru doped three dimensional (3D) porous Ni₃N spheres, with tannic acid (TA) and urea as the carbon and nitrogen resources, is synthesized via hydrothermal and low-temperature treated process (Ru–Ni₃N@NC). The porous nanostructure of Ni₃N and the nickel foam provide abundant active sites and channel during catalytic process. Moreover, Ru doping and rich defects favor to boost the reaction kinetics by optimizing the adsorption/desorption or dissociation of intermediates and reactants. The above advantages enable Ru–Ni₃N@NC to have good bifunctional catalytic performance in alkaline media. Only 43 and 270 mV overpotentials are required for hydrogen evolution (HER) and oxygen evolution (OER) reactions to drive a current of 10 mA cm^?2. Moreover, it also showed good electrocatalytic performance in neutral and alkaline seawater electrolytes for HER with 134 mV to drive 10 mA cm^?2 and 83 mV to drive 100 mA cm^?2, respectively. Remarkably, the as-designed Ru–Ni₃N@NC also owns extraordinary catalytic activity and stability toward UOR. Moreover, using the synthesized Ru–Ni₃N@NC nanomaterial as the anode and cathode of urea assisted water decomposition, a small potential of 1.41 V was required to reach 10 mA cm^?2. It can also be powered by sustainable energy sources such as wind, solar and thermal energies. In order to make better use of the earth's abundant resources, this work provides a new way to develop multi-functional green electrocatalysts.     

Dual functions of three-dimensional hierarchical architecture on improving the rate capability and cycle performance of LiNi0.8Co0.1Mn0.1O2 cathode material for lithium-ion battery

The main obstacles in lithium-ion battery are limited by rate performance and the rapid capacity fading of LiNi_0.8Co_0.1Mn_0.1O₂ (NCM811). Herein, a novel three-dimensional (3D) hierarchical coating material has been fabricated by in situ growing carbon nanotubes (CNTs) on the surfaces of Ni–Al double oxide (Ni–Al-LDO) sheets (named as LDO&CNT) with Ni–Al double hydroxide (Ni–Al-LDH) as both the substrate and catalyst precursor. The resultant LDO&CNT nanocomposites are uniformly coated on the surfaces of NCM811 by the physical mixing method. The rate capability of the resultant cathode material retains to 78.80% at a current rate of 3C. Its capacity retention increases by 6.7–14.42% compared with pristine NCM811 after 100 cycles within a potential range of 2.75–4.3 V at 0.5C. The improved rate capability and cycle performance of NCM811 are assigned to the synergistic effects between Ni–Al-LDO and CNTs. The hierarchical LDO&CNT nanocomposites coating on the surface of NCM811 avoids the aggregation of conductive CNTs and the stacking of Ni–Al-LDO nanosheets. Furthermore, it accelerates Li⁺ and electrons shuttle and reduces the reaction of Li₂O with H₂O and CO₂ in air, which results in Li₂CO₃ and LiOH alkali formation on the NCM811 surface.     

Enhanced structural,electromagnetic and absorption features of CoSm ferrite-metamaterial absorbers through synergistic effects

Currently, materials with outstanding absorption abilities, such as thin size, better absorbing power, and light weight are the need of industry to resolve the electromagnetic issues. However, the research on optimizing the composition of the material, microstructure and the structure of the absorber are also the important factors for enhancing the absorption features. A metamaterial microwave absorber (MMA) based on nano ferrites with desirable absorption peaks is proposed and simulated. Sol-gel auto combustion route is used to prepare the nanosized Sm doped Co ferrite with Co_1+xSm_xFe_2-2xO₄ at x = 0.00, 0.03, 0.06, 0.09, respectively. XRD, VSM, FESEM, and VNA were employed to evaluate the structural, magnetic, morphological, and dielectric features. Rietveld refinement of the XRD patterns of samples was evaluated. Refined parameters show the spinel phase's emergence and the Fe₂O₃ phase. Grain size and crystallite size were increased with Sm doping in Co ferrite. Electromagnetic studies depicted that the highest dielectric constant value was found at x = 0.09 and the minimum value at x = 0.03, respectively. Sm doped Co ferrite at x = 0.09 depicted high Q values at higher frequencies. The coercivity values first decreased and then increased. All samples exhibit variations in coercivity and magneto-crystalline anisotropy constant. This variation was attributed to the super-exchange interactions and strong LS coupling of the cations. The multiple absorption peaks are attained for TE-polarization, and the absorptivity is considerably improved for x = 0.09. The proposed absorber simulated from CST depicted the absorption peaks of the S-band and C-band of the microwave regime. The synergistic effects among the metamaterial and ferrite layers may enhance the absorption feature and would be useful for satellite communication applications.     

Potentiality of combined catalyst for high quality bio-oil production from catalytic pyrolysis of pinewood using an analytical Py-GC/MS and fixed bed reactor

The aim of this study was to investigate the potential of combined catalyst (ZSM-5 and CaO) for high quality bio-oil production from the catalytic pyrolysis of pinewood sawdust that was performed in Py-GC/MS and fixed bed reactor at 500 °C. In Py-GC/MS, the maximum yield of aromatic hydrocarbon was 36 wt% at biomass to combined catalyst ratio of 1:4 where the mass ratio of ZSM-5 to CaO in the combined catalyst was 4:1. An increasing trend of phenolic compounds was observed with an increasing amount of CaO, whereas the highest yield of phenolic compounds (31 wt%) was recorded at biomass to combined catalyst ratio of 1:4 (ZSM-5: CaO - 4:1). Large molecule compounds could be found to crack into small molecules over CaO and then undergo further reactions over zeolites. The water content, higher heating value, and acidity of bio-oil from the fixed bed reactor were 21%, 24.27 MJkg⁻¹, and 4.1, respectively, which indicates that the quality of obtained bio-oil meets the liquid biofuel standard ASTM D7544-12 for grade G biofuel. This research will provide a significant reference to produce a high-quality bio-oil from the catalytic pyrolysis of woody biomass over the combined catalyst at different mass ratios of biomass to catalyst.     

Improved reversible dehydrogenation properties of MgH2 by the synergetic effects of graphene oxide-based porous carbon and TiCl3

In this study, we used a combination of graphene oxide-based porous carbon (GC) and titanium chloride (TiCl₃) to improve the reversible dehydrogenation properties of magnesium hydride (MgH₂). Examining the effects of GC and TiCl₃ on the hydrogen storage properties of MgH₂, the study found GC was a useful additive as confinement medium for promoting the reversible dehydrogenation of MgH₂. And TiCl₃ was an efficient catalytic dopant. A series of controlled experiments were carried out to optimize the sample preparation method and the addition amount of GC and TiCl₃. In comparison with the neat MgH₂ system, the MgH₂/GC-TiCl₃ composite prepared under optimized conditions exhibited enhanced dehydrogenation kinetics and lower dehydrogenation temperature. A combination of phase/microstructure/chemical state analyses has been conducted to gain insight into the promoting effects of GC and TiCl₃ on the reversible dehydrogenation of MgH₂. Our study found that GC was a useful scaffold material for tailoring the nanophase structure of MgH₂. And TiCl₃ played an efficient catalytic effect. Therefore, the remarkably improved dehydrogenation properties of MgH₂ should be attributed to the synergetic effects of nanoconfinement and catalysis.     

Melting heat transfer analysis of electrically conducting nanofluid flow over an exponentially shrinking/stretching porous sheet with radiative heat flux under a magnetic field

Modern magnetic nanomaterial processing operations are progressing rapidly and require increasingly sophisticated mathematical models for their optimization. Stimulated by such developments, in this paper, a theoretical and computational study of a steady magnetohydrodynamic nanofluid over an exponentially stretching/shrinking permeable sheet with melting (phase change) and radiative heat transfer is presented. Besides, wall transpiration, that is, suction and blowing (injection), is included. This study deploys Buongiorno's nanofluid model, which simulates the effects of the Brownian motion and thermophoresis. The transport equations and boundary conditions are normalized via similarity transformations and appropriate variables, and the similarity solutions are shown to depend on the transpiration parameter. The emerging dimensionless nonlinear coupled ordinary differential boundary value problem is solved numerically with the Newton-Fehlberg iteration technique. Validation with special cases from the literature is included. The increase in the magnetic field, that is, the Hartmann number, is observed to elevate nanoparticle concentration and temperature, whereas it dampens the velocity. Higher values of the melting parameter consistently decelerate the boundary layer flow and suppress temperature and nanoparticle concentration. A higher radiative parameter strongly increases temperature (and thermal boundary layer thickness) and weakly accelerates the flow. The increase in the Brownian motion reduces nanoparticle concentrations, whereas a greater thermophoretic body force strongly enhances them. The Nusselt number and Sherwood number are observed to be decreased with an increasing Hartmann number, whereas they are elevated with a stronger wall suction and melting parameter.     

Ontogenetic habitat use and seasonal activity of Nile crocodiles (Crocodylus niloticus) in the Lake Albert delta,East Africa

Crocodiles play important roles in many ecosystems, but their populations worldwide are threatened by human exploitation and habitat destruction. We studied ontogenetic changes in habitat use and seasonal activity patterns in a population of Nile crocodiles (Crocodylus niloticus) inhabiting the Lake Albert Delta Wetland System, a Ramsar Site of international importance in Murchison Falls National Park of western Uganda. A total of 186 crocodile observations were made from monthly surveys of five transects during October 2017 to September 2018. Crocodiles exhibited a marginally bi-modal seasonal pattern, with the fewest observations from July to August and October to November, and the highest observations from January to February and April to May. Crocodiles were most frequently encountered along the north shore of the delta, especially on riverbanks with woody vegetation, followed by Cyperus papyrus-Vossia dominated habitats, while crocodiles were infrequently observed on islands and muddy banks. Habitat niche breadth was narrowest in hatchlings and widest in sub-adults, with juveniles and large adults exhibiting intermediate values. Overlap in habitat resource use across size classes was generally high, with the lowest overlap between hatchlings and juveniles, and the highest between large and sub-adult crocodiles. Our study on Nile crocodiles in the Lake Albert delta provides insights into habitat partitioning among different demographic segments of this population that can be utilized to improve its management in one of Africa’s Great Lakes by spatially and temporally focusing conservation efforts on the most used habitats and seasonal aggregations, respectively.     

Integrated energy efficiency evaluation of a multi-source multi-load desalination micro-energy network

With increasing global shortage of fresh water resources, many countries are prioritizing desalination as a means of utilizing abundantly available seawater resources. Integrated energy efficiency evaluation is a scientific method for the quantitative analysis of energy efficiency based on multiple indicators and is very useful for investment, construction, and scientific decision-making for desalination projects. In this paper, the energy efficiency evaluation of the micro energy network (MEN) of desalination for multi-source and multi-load is studied, and the basic idea of comprehensive energy efficiency evaluation is analyzed. The process includes the use of a MEN model to establish an integrated energy efficiency evaluation index system, taking into consideration energy, equipment, economic, environmental, and social factors. A combined evaluation method considering subjective and objective comprehensive weights for multi-source multi-load desalination MENs is proposed to evaluate the energy efficiency of desalination and from multiple perspectives.